What is the Flex Capacitor 60-75?
The Flex Capacitor is a super lightweight, supportive pack that is ideal for trekking and backpacking thanks to its 15-litres of expandable volume, all the while weighing just 1.2kg (approx).
What is it made of?
The pack is made using a 100D nylon/polyester ripstop fabric with a 420D nylon reinforcement on the base. The main 100D fabric is lightweight yet tough enough to deal with prolonged mountain use and the 420D base just gives it that added bit of abrasion resistance.
Which backsystem does it use?
The Flex Capacitor uses a fairly simple but effective system comprising of three padded mesh sections that sit against you to provide comfort and support. This leaves a gap in the centre of the back for sweat to escape, making it a lot more comfortable during warmer months of the year. The hipbelt and shoulder straps use the same mesh-layered foam and offer plenty of comfort when the pack is loaded.
This backsystem is supported by a 'Y' shaped frame that runs up the inside of the pack. This 'Y' shape means the lower half of the pack can twist and turn with your hips while the upper half stays still for greater structure and support.
What are its features?
Perhaps the most unique feature of this pack is its size range. The Flex Capacitor features 15-litres of expandable storage, taking it from 60 to 75. This makes it the ideal trekking/backpacking rucksack where you'll probably start with more kit than you finish with.
Other useful features include two stretch mesh side pockets for bottles, two mesh hydration pockets on the shoulders for more water storage, zipped hipbelt pockets (snack pockets) and a small pocket in the lid for bits you need to access quickly. A U-shaped top zip allows you to gain full access to your stuff without any faffing. The outside of the pack is absolutely covered in compression straps, letting you cinch the pack down to pull the weight closer to your back for a more comfortable carry.
- Expandable volume
- Two stretch mesh pockets
- Two mesh hydration pockets on shoulder straps
- Zipped hipbelt pockets
- U-shaped top access zip
- Stash pocket in lid
- Lightweight design
- Tough fabrics with reinforced base
- Y-shaped internal frame
Getting the correct fit for your rucksack is as important as getting the fit right for your boots. A badly fitting pack can inflict misery and discomfort and completely ruin your adventure. This guide is designed to help you get the best fit and comfort from your chosen pack so that carrying all your kit becomes a pleasure and not a chore.
ADJUSTING THE BACK LENGTH
If the pack has an adjustable back length, adjust this to your correct level. Your back length is not related to your height but your torso length. Many packs, and specifically the bigger and more technical packs are available in different back lengths or feature adjustable back systems. Contrary to popular belief, your torso length and not your overall height is the key to getting a well fitted pack. Tall people don’t necessarily have long torsos, just as shorter people don’t always have a short torso length.
Your torso length can be found by measuring from your C7 vertebra (the bony protrusion at the back of your neck when looking down) to the height of your iliac crest (top of your hip bones, where you put your hands on your hips). This measurement will give you an idea of which pack back length to choose.
Once you've got the back length sorted, either by selecting the correct size pack or adjusting the back system, you can begin to follow these simple steps to help achieve a comfortable carry.
LOOSEN OFF ALL STRAPS
Before you start fitting the pack, loosen off all the straps as this will make it easier to get the correct tension later.
TIGHTENING THE HIPBELT
Fasten the backpack hipbelt, the general position is the same as where you’d put your ‘hands on hips’ This area is called the pelvic girdle, and what you can feel when you rest your hand on the area is the bony protuberance, the iliac crest. The iliac crest can support the weight from a pack comfortably, and for sustained periods. The padded section of the hipbelt should encompass this and fit securely.
Tighten the straps so the hipbelt feels secure and held firmly around your body. Ensure that the lumbar pad is centered to your lower back to give you maximum support. Remember that your hips carry most of the weight of the pack, so this should be firm but comfortable.
ADJUSTING THE SHOULDER STRAPS
Next, adjust the shoulder straps, pull them until they start to become snug, but ensure that they are not too tight as to lift the pack off your hips. Remember tightening them will stabilise the pack but will increase pressure over the shoulders. If the back length of the pack is correct the shoulder straps will be flush to your shoulders whilst the hipbelt sits in place comfortably. The point where the shoulder straps attach to the main body of the pack should be roughly half way down your shoulder blades; this ensures that the shoulder straps rolls evenly over the top of your shoulders to distribute the weight correctly.
FASTENING THE CHEST STRAP
Fasten the chest strap and pull until taut but not tight, the elastic section should not be extended. This helps keep the shoulder straps from catching in your shoulder joints and keeps the stability of the pack when moving over rough ground.
ADJUSTING THE TOP TENSIONERS
Top tensioner straps link the shoulder straps to the top of the pack. When tightened, their main function is to stabilise the top part of the pack. The optimum angle for these straps in 45º, but they will stabilise the load even when horizontal or at a more obtuse angle. Tighten them until you feel the top part of the pack rest against your pack, over tightening them will create excessive pressure on the front of your shoulders.
ADJUSTING THE SIDE TENSIONERS
Side tension straps are linked to the hipbelt. By tightening these straps you can stabilise the load but reduce the hipbelt flexibility. Where balance is critical tightening them can help you feel more secure. However, if you are striding out over easy terrain it’s better to loosen these straps to allow full hip flexibility.
ADJUSTING THE SIDE COMPRESSION STRAPS
Side compression straps come next, pulling these tight does two things: firstly, it stabilises the load, secondly it can lift the lower part of the pack, repositioning the load closer to your back.
ADJUSTMENTS ON THE GO
Following these steps should give you a comfortable but secure fit on your pack. Sometimes adjustments will need to be made on the go depending on the terrain or the load you are carrying. The perfect fit is very much a personal preference so experiment with different tensions on the pack to find what suits you best.